Question 346
Refer to the exhibit.
An engineer configured the New York router with state routes that point to the Atlanta and Washington sites.
When command must be configured on the Atlanta and Washington routers so that both sites are able to reach the loopback2 interface on the New York router?
An engineer configured the New York router with state routes that point to the Atlanta and Washington sites.
When command must be configured on the Atlanta and Washington routers so that both sites are able to reach the loopback2 interface on the New York router?
Question 347
Lab Simulation 50
Guidelines
This is a lab item in which tasks will be performed on virtual devices.
- Refer to the Tasks tab to view the tasks for this lab item.
- Refer to the Topology tab to access the device console(s) and perform the tasks.
- Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
- All necessary preconfigurations have been applied.
- Do not change the enable password or hostname for any device.
- Save your configurations to NVRAM before moving to the next item.
- Click Next at the bottom of the screen to submit this lab and move to the next question.
- When Next is clicked, the lab doses and cannot be reopened.
Topology
Tasks
All physical cabling is in place. Router R4 and PC1 are fully configured and inaccessible. R4's WAN interfaces use .4 in the last octet for each subnet. Configurations should ensure that connectivity is established end-to-end.
1. Configure static routing to ensure R1 prefers the path through R2 to reach only PC1 on R4's LAN
2. Configure static routing that ensures traffic sourced from R1 will take an alternate path through R3 to PC1 in the event of an outage along the primary path
3. Configure default routes on R1 and R3 to the Internet using the least number of hops
Guidelines
This is a lab item in which tasks will be performed on virtual devices.
- Refer to the Tasks tab to view the tasks for this lab item.
- Refer to the Topology tab to access the device console(s) and perform the tasks.
- Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
- All necessary preconfigurations have been applied.
- Do not change the enable password or hostname for any device.
- Save your configurations to NVRAM before moving to the next item.
- Click Next at the bottom of the screen to submit this lab and move to the next question.
- When Next is clicked, the lab doses and cannot be reopened.
Topology
Tasks
All physical cabling is in place. Router R4 and PC1 are fully configured and inaccessible. R4's WAN interfaces use .4 in the last octet for each subnet. Configurations should ensure that connectivity is established end-to-end.
1. Configure static routing to ensure R1 prefers the path through R2 to reach only PC1 on R4's LAN
2. Configure static routing that ensures traffic sourced from R1 will take an alternate path through R3 to PC1 in the event of an outage along the primary path
3. Configure default routes on R1 and R3 to the Internet using the least number of hops
Question 348
Refer to the exhibit.
How should the configuration be updated to allow PC1 and PC2 access to the Internet?
How should the configuration be updated to allow PC1 and PC2 access to the Internet?
Question 349
An engineer is configuring NAT to translate the source subnet of 10.10.0.0/24 to any of three addresses
192.168.30.1, 192.168.3.2, 192.168.3.3 Which configuration should be used?
192.168.30.1, 192.168.3.2, 192.168.3.3 Which configuration should be used?
Question 350
Connectivity between four routers has been established. IP connectivity must be configured in the order presented to complete the implementation. No dynamic routing protocols are included.
1. Configure static routing using host routes to establish connectivity from router R3 to the router R1 Loopback address using the source IP of 209.165.200.230.
2. Configure an IPv4 default route on router R2 destined for router R4.
3. Configure an IPv6 default router on router R2 destined for router R4.
1. Configure static routing using host routes to establish connectivity from router R3 to the router R1 Loopback address using the source IP of 209.165.200.230.
2. Configure an IPv4 default route on router R2 destined for router R4.
3. Configure an IPv6 default router on router R2 destined for router R4.