Free Access Cisco.300-510.v2025-06-23.q161 Practice Test (Page 26)

Question 121

Refer to the exhibit.

A network engineer must enable segment routing between the three autonomous systems with these requirements:
OSPF link-state data for area 0 routers must be distributed to the controller via BGP LS.
EPE must be enabled on the egress node in AS 100.
Routers must advertise peer node SIDs to the controller R1 via BGP LS.
Which configuration must the engineer apply?

Question 122

Refer to the exhibit.

Which effect of this configuration is true?

A.It sets the hold timer to 30 milliseconds and the keepalive timer to 240 milliseconds

B.It sets the keepalive timer to 30 milliseconds and the hold timer to 240 milliseconds

C.It sets the hold timer to 30 seconds and the keepalive timer to 240 seconds

D.It sets the keepalive timer to 30 seconds and the hold timer to 240 seconds.

Question 123

Refer to the exhibit.

Why is neighbor 10.1.5.5 stuck in "2WAY" state?

A.Router ID 10.1.5.5 is not reachable from R2

B.OSPF parameters (Area ID or hello interval) are mismatched between R2 and 10.1.5.5

C.OSPF authentication has failed between R2 and 10.1.5.5

D.It is an expected behavior when OSPF network type is broadcast

Question 124

Refer to the exhibit.

An engineer is troubleshooting an OSPF issue. Router 1 has a neighbor relationship with router 2. Only router 1 classful EIGRP routes can be seen on router 2. In order for all EIGRP routes to be redistributed correctly, which action should be taken?

A.Router 1 must have the keyword metric-type 1 included in the redistribution command for all EIGRP routes to be redistributed.

B.Router 1 must have the keyword included in the redistribution command for all EIGRP routes to be redistributed.

C.Router 1 must remove the AS number 1 from the redistribution command for all EIGRP routes to be redistributed.

D.Router 1 must have the keyword ospf-metric included in the redistribution command for all EIGRP routes to be redistributed.

Question 125

Refer to the exhibit.

Which task must be performed on interface g1/0/0 to complete the SSM implementation?

A.enable CDP

B.disable IGMP

C.configure IGMPv3

D.configure OSPFv3

Other Version: 2444Cisco.300-510.v2024-09-24.q207; 1895Cisco.300-510.v2023-09-09.q129; 2218Cisco.300-510.v2023-06-10.q145; 2699Cisco.300-510.v2022-09-29.q110; 2917Cisco.300-510.v2022-08-02.q105; 4379Cisco.300-510.v2022-02-01.q126; 63Cisco.Actualtestpdf.300-510.v2021-11-18.by.queena.92q.pdf

Latest Upload: 240PaloAltoNetworks.NGFW-Engineer.v2026-05-01.q43; 335Nokia.4A0-113.v2026-05-01.q69; 344EC-COUNCIL.312-49v11.v2026-04-30.q214; 271Microsoft.MB-820.v2026-04-30.q101; 237Salesforce.MC-202.v2026-04-30.q57; 250BICSI.INSTC_V8.v2026-04-29.q53; 369NMLS.MLO.v2026-04-28.q82; 267NCARB.Project-Management.v2026-04-28.q27; 484EMC.D-AV-DY-23.v2026-04-27.q184; 1240ServiceNow.CSA.v2026-04-27.q483

Question 121

Question 122

Question 123

Question 124

Question 125

Download PDF File