Free Access Cisco.300-615.v2022-05-28.q107 Practice Test (Page 4)

Question 11

Refer to the exhibit.

An engineer must strictly enforce the port security configuration database in the Fibre Channel fabric. A new device has been connected to the Fibre Channel storage interface that was configured for port security. The port security was enabled for the VSAN that the port belongs to. Despite the configuration, the rogue devices can log into the fabric. Which action resolves the issue?

A.Disable auto learn in VSAN 1 with the no port-security auto-learn vsan 1 command

B.Disable CFS distribution with the no port-security distribute vsan 1 command

C.Commit the active database with the port-security database copy vsan 1 command

D.Commit the changes with the port-security commit copy vsan 1 command

Question 12

Refer to the exhibit.

Sw1 and Sw2 are two Cisco Nexus 9000 Series Switches that run Cisco NX-OS. They are VTEPs in the same vPC domain. Which statement describes what happens in this scenario?

A.Sw1 drops all traffic because there is no (S, G) OIF list to encapsulate VXLAN multicast packets and send them out to the underlay network through the uplink interfaces.

B.Sw1 and switch 2 perform the VxLAN multicast encapsulation and decapsulation for all traffic associated with the VxLAN VNIs, depending on the hashing.

C.Sw1 performs the VxLAN multicast encapsulation and decapsulation for all traffic associated with the VxLAN VNIs.

D.Sw2 did not send an IP PIM register to the rendezvous point for the multicast group of the VXLAN VNI.

Question 13

An engineer is troubleshooting a failed DCBX exchange between a server and a Cisco Nexus switch. Which action allows DCBX to successfully negotiate?

A.Enable ETS

B.Enable PFC.

C.Enable Cisco Discovery Protocol.

D.Enable LLDP.

Question 14

You have an ACI environment with three APICs, two spine switches, and four-leaf switches. You wipe and reboot all APICs first then leaf and spine switches one-by-one and successfully go through the Initial Setuo dialogue on the APIC 1 CIMC KVM console. When you log in to the APIC1 WebGUI, you notice that you do not see any directly connected leaf switches being discovered under Fabric > Inventory > Fabric Membership. What is the cause of the issue?

A.The leaf nodes were not erased properly, which caused a fabric parameters mismatch with the APIC1.

B.Rebooting the APICs and the leaf and spine switches after wiping them is not required.

C.You forgot to enter the TEP Pool value during the Initial Setup dialogue on APIC1.

D.The same Fabric Name value should be used before after wiping all devices.

Question 15

Refer to the exhibit.

vPC between switch1 and switch2 is not working. Which two actions are needed to fix the problem? (Choose two.)

A.Configure one of the switches as primary for the vPC.

B.Configure vPC peer link and vPC peer keepalive correctly.

C.Activate VLANs on the vPC.

D.Match vPC domain ID between the two devices.

E.Configure IP address on the interface.

Other Version: 407Cisco.300-615.v2024-09-25.q117; 795Cisco.300-615.v2023-01-31.q58; 2243Cisco.300-615.v2022-10-01.q126; 2399Cisco.300-615.v2022-05-03.q107; 93Cisco.Exams4sures.300-615.v2021-11-23.by.tess.99q.pdf

Latest Upload: 105OCEG.GRCP.v2025-09-11.q211; 104HP.HPE0-V27.v2025-09-11.q78; 118Oracle.1Z0-1057-23.v2025-09-10.q47; 151Google.Professional-Cloud-Network-Engineer.v2025-09-09.q179; 131SAP.C-S4EWM-2023.v2025-09-08.q83; 165TheSecOpsGroup.CNSP.v2025-09-08.q20; 223CFAInstitute.ESG-Investing.v2025-09-08.q173; 170PECB.ISO-IEC-27001-Lead-Implementer.v2025-09-06.q132; 150Salesforce.Data-Architect.v2025-09-05.q216; 144Adobe.AD0-E605.v2025-09-05.q50

Question 11

Question 12

Question 13

Question 14

Question 15

Download PDF File