Online Access Free AZ-802 Practice Test

You have an on-premises server named Server1 that runs Windows Server and contains the shares shown in the following table.
You have an Azure subscription named Sub1 that contains an Azure Storage Mover resource named Mover1 and the storage accounts shown in the following table.
The storage accounts contain the resources shown in the following table.
For each of the following statements, select Yes if the statement is true. Otherwise, select No.
NOTE: Each correct selection is worth one point.

Exhibit

Exhibit

Exhibit

Correct Answer:

Explanation:
Azure Storage Mover ' s supported combinations of source and target allow an SMB-based source share to be migrated to an Azure file share, so Share1, which uses the SMB protocol, can be migrated to azshare1, an Azure file share hosted on storage1, a premium-performance FileStorage account, and that combination is fully supported. Share2, however, is an NFS-based source share, and Storage Mover only supports migrating an NFS source directly to an Azure file share when that destination file share itself uses the NFS 4.1 protocol, which in turn requires the destination storage account to be a premium-performance FileStorage account rather than a general-purpose standard account; azshare2 lives on storage2, which the exhibit shows is a standard-performance general-purpose v2 (StorageV2) account, and standard general-purpose accounts cannot host NFS-protocol Azure file shares, so this particular migration combination is not supported and the answer is No. Storage Mover does, however, separately support migrating an NFS source directly to an Azure blob container, provided that the destination storage account has the hierarchical namespace feature enabled, and the exhibit confirms that storage2 has hierarchical namespace enabled even though it is a standard account, so Share2 can still be successfully migrated to the azcont1 blob container that also resides on storage2, making that particular combination supported.

You have an Azure subscription. The subscription contains a virtual machine named VM1 that runs Windows Server. The subscription contains the storage accounts shown in the following table: storage1 (Standard, GRS), storage2 (Standard, ZRS), storage3 (Premium, Block blobs, LRS), storage4 (Premium, File shares, LRS). You plan to enable boot diagnostics for VM1. You need to configure storage for the boot diagnostics logs and snapshots. Which storage account should you use?

Storage accounts table

• A.storage1
• B.storage3
• C.storage2

You have an on-premises server named Server1 that runs Windows Server. You need to perform an on- demand backup of the files on Server1 by using Azure Backup. Which five actions should you perform in sequence? To answer, move the appropriate actions from the list of actions to the answer area and arrange them in the correct order.
You have an on-premises server named Server1 that runs Windows Server. You need to perform an on- demand backup of the files on Server 1 by using Azure Backup.
Which five actions should you perform in sequence? To answer, move the appropriate actions actions from the list of actions to the answer are and arrange them in the correct order.

Correct Answer:

Explanation:
1. From the Azure portal, create a Recovery Services vault. 2. From the Azure portal, download the Microsoft Azure Recovery Services (MARS) agent and the vault credentials. 3. On Server1, run the Microsoft Azure Recovery Services Agent Setup Wizard. 4. On Server1, run the Register Server Wizard. 5. On Server1, run the Schedule Backup Wizard.
Backing up an on-premises server ' s files with Azure Backup begins in the Azure portal, where a Recovery Services vault must be created first, since that vault is the resource both the agent installer and the vault registration credentials are subsequently generated from and downloaded through. Still from the Azure portal, the administrator downloads the Microsoft Azure Recovery Services agent installer together with its matching vault credentials file, both of which are needed for the next steps on the server itself. On Server1, running the Microsoft Azure Recovery Services Agent Setup Wizard actually installs the MARS agent software locally, after which the Register Server Wizard uses the previously downloaded vault credentials to register Server1 against that specific vault, a step that necessarily comes after both the vault ' s creation and the credentials download. With the agent successfully installed and Server1 registered, running the Schedule Backup Wizard on Server1 lets the administrator select which files and folders to protect, define a retention policy, and trigger the initial on-demand backup, completing the workflow the requirement calls for.

You have an Azure subscription that contains the storage accounts shown in the following table. In the West US Azure region, you create a storage sync service named SyncA. You plan to create a sync group named GroupA. What is the maximum number of cloud endpoints you can use with GroupA?

Storage accounts table

• A.4
• B.3
• C.2
• D.1

You have an on-premises server that runs Windows Server and contains a folder named Folder1. Folder1 contains 50 GB of files.
You have an Azure subscription that contains an Azure Files share named share1.
You need to migrate the data in Folder1 to share1.
What should you do? To answer, select the appropriate options in the answer area.
NOTE: Each correct selection is worth one point.

Correct Answer:

Explanation:
Deploy to Azure: An Azure Storage account. Install on Server1: The Azure File Sync agent.
An Azure Files share such as share1 is always hosted inside an Azure Storage account, so an Azure Storage account is what share1 is actually deployed into and depends on existing in the subscription; it is not deployed to a Storage Sync Service instance, an Azure Migrate project, an on-premises data gateway, or an ArcBox environment, none of which host file shares. To move Folder1 ' s 50 GB of files from the on-premises server into share1 while keeping both locations synchronized rather than performing a single one-time copy, the documented approach is to install the Azure File Sync agent directly on the on-premises server, then create a sync group that pairs Folder1, registered as a server endpoint, with share1, registered as the cloud endpoint.
Once that sync relationship is established, Azure File Sync uploads Folder1 ' s existing files up to share1 and then keeps both the on-premises folder and the cloud share synchronized going forward, which is Microsoft ' s documented approach for migrating on-premises file server content into Azure Files rather than using the Azure Connected Machine agent, Storage Migration Service, or Storage Replica, none of which target an Azure Files share as their destination in this way.