Explanation
Before a retransmission, the CWmax (Contention Window maximum) value doubles and increases by 1. The CWmax is a parameter that determines the upper limit of the random backoff time that a STA (station) has to wait before attempting to access the medium. The random backoff time is chosen from a range of values between CWmin (Contention Window minimum) and CWmax. The CWmin and CWmax values depend on the AC (Access Category) of the traffic and the PHY type of the STA. If a transmission fails due to a collision or an error, the STA has to retransmit the frame after waiting for another random backoff time. However, to reduce the probability of another collision, the STA increases its CWmax value by doubling it and adding 1.
This increases the range of possible backoff values and spreads out the STAs more evenly. The STA resets its CWmax value to its original value after a successful transmission or after reaching a predefined limit. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 7: QoS Analysis, page
196-197

Explanation
The function of the PHY preamble is to allow the receiver to detect and synchronize with the signal. The PHY preamble is a part of the PPDU that is transmitted before the PHY header and the PSDU. The PHY preamble consists of a series of training fields that help the receiver to adjust its parameters, such as frequency, timing, and gain, to match the incoming signal. The PHY preamble also helps the receiver to estimate the channel conditions and noise level. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 4:
802.11 Physical Layer, page 99-100

Explanation
A hexadecimal value is a value that uses base 16 notation, which means it can have digits from 0 to 9 and letters from A to F. A hexadecimal value is usually preceded by 0x to indicate that it is hexadecimal and not decimal or binary. For example, 0x0A is hexadecimal for 10 in decimal or 00001010 in binary. The other options are not valid prefixes for hexadecimal values.References:
CWAP-404 Study Guide, Chapter 2: Protocol Analysis, page 35
CWAP-404 Objectives, Section 2.2: Analyze field values

Explanation
In the 2.4 GHz band, probe requests are usually sent at the minimum basic rate from an unassociated STA. A probe request is a type of management frame that is transmitted by a STA to discover available BSSs in its vicinity. A probe request can be sent on one or more channels in either passive or active scanning mode. In passive scanning mode, a STA listens for beacon frames from APs on each channel. In active scanning mode, a STA sends probe requests on each channel and waits for probe responses from APs. A probe request is usually sent at the minimum basic rate, which is the lowest data rate among the supported rates that is required for all STAs to join and communicate with a BSS. The minimum basic rate can vary depending on the configuration of each BSS, but it is typically one of these values: 1 Mbps, 2 Mbps, 5.5 Mbps, or 11 Mbps in the 2.4 GHz band. The other options are not correct, as they do not reflect how probe requests are usually sent in the 2.4 GHz band. MCS 0 is a modulation and coding scheme used by 802.11n/ac devices in either band, but it is not a data rate per se. 6 Mbps is a data rate used by OFDM devices in either band, but it is not usually configured as a minimum basic rate in the 2.4 GHz band. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 5: 802.11 MAC Sublayer, page 123-124

Explanation
When performing protocol analysis, you would look at the HT Information Element in the Beacon frame to determine which one of the four HT protection modes the AP is operating in. The HT Information Element contains various subfields that provide information about the HT network configuration and operation. One of these subfields is the HT Protection field, which indicates whether any protection mechanisms are required for mixed-mode operation with non-HT STAs. The four possible values for this field are:
No Protection: No protection mechanisms are required.
Non-member Protection: RTS/CTS or CTS-to-self protection is required for all HT transmissions.
20 MHz Protection: RTS/CTS or CTS-to-self protection is required for all HT transmissions using a 40 MHz channel.
Non-HT Mixed Mode: All HT transmissions must use a non-HT preamble and header . References:
CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 11:
802.11n/ac/ax PHYsical Layer Frame Exchanges, page 378; CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 11: 802.11n/ac/ax PHYsical Layer Frame Exchanges, page 379.