Free Access CWNP.CWDP-305.v2025-08-21.q200 Practice Test (Page 29)

Question 136

In addition to a copy of your design, which tools should you provide to ensure the installation team correctly deploys access points (APs) in the specified locations within a multi-floor indoor design?

A.Camera and marking tools

B.RF spectrum analyzer and packet capturing software

C.Ladder and a pen

D.GPS and a map

Question 137

Who should be present from the customer side during the final meeting after successfully implementing a WLAN infrastructure?

A.Acquirer and stakeholders

B.End-users

C.Remote workers

D.The customer's customers

Question 138

Main Topic:ProtocolandSpectrum Analysis
Question:
What part of the 802.11n preamble is used by the receiver to estimate the spatially multiplexed signal channel? What mode is this used in?

A.HT-STF in Greenfield mode only

B.HT-LTF in Mixed and Greenfield modes

C.HT-LTF in Greenfield mode only

D.HT-STF in Mixed and Greenfield modes

Question 139

While configuring your site survey software for an upcoming manual survey project, you notice the configuration option for "Network Card Simul-ation". What is the purpose of such a feature and when would you use it?

A.This setting allows the site survey software to convert the APs measured downlink RF data into a simulated data set as if the same data were transmitted by a specific client station. It is useful for determining uplink client performance when clients are located far from APs as well as projecting cell size for ad hoc networks.

B.Since WLAN adapters are not typically calibrated by manufacturers, this setting is a form of software calibration in which you can calibrate an (uncalibrated) adapter to match one of the calibrated adapters shown in the list. This process improves the reliability of RF data collection and reporting when uncalibrated adapters are used.

C.This is the configuration area in which you specify the adapter type that will be used for the site survey so that the survey software can interpret that adapter's reported metrics (based on proprietary formulas) into an RF measurement that is standardized by the survey software and known to its users. This is done for every survey.

D.The site survey software manufacturer allows you to view the collected RF data as if it were collected by a different type of adapter. This functionality allows you to review survey data to determine how the RF environment will likely look based on the receive sensitivity and other RF capabilities of a specific client.

Question 140

When a WLAN controller sends an 802.11 frame to a lightweight AP for transmission on the wireless medium, how does it mark the frame for 802.11 QoS priority?

A.The WLAN controller will place the user priority (UP) value in the QoS Control field of the 802.11 frame header before passing it to the lightweight AP.

B.The WLAN controller does not mark 802.11 frames with priority values; only the APs can do this.

C.The WLAN controller does not mark the 802.11 frames with priority values; only the Layer 3 switches can do this.

D.The WLAN controller does not mark the 802.11 frames with priority values; only the Layer 3 routers can do this.

Other Version: 892CWNP.CWDP-305.v2026-03-09.q251

Latest Upload: 203PaloAltoNetworks.NGFW-Engineer.v2026-05-01.q43; 302Nokia.4A0-113.v2026-05-01.q69; 261EC-COUNCIL.312-49v11.v2026-04-30.q214; 230Microsoft.MB-820.v2026-04-30.q101; 212Salesforce.MC-202.v2026-04-30.q57; 207BICSI.INSTC_V8.v2026-04-29.q53; 336NMLS.MLO.v2026-04-28.q82; 244NCARB.Project-Management.v2026-04-28.q27; 466EMC.D-AV-DY-23.v2026-04-27.q184; 1123ServiceNow.CSA.v2026-04-27.q483

Question 136

Question 137

Question 138

Question 139

Question 140

Download PDF File