Free Access H3C.GB0-341-ENU.v2022-03-08.q89 Practice Test (Page 15)

Question 66

Which of the following statements about indoor PAP installation specifications is correct? (Multiple choice)

A.The AP installation location must meet the engineering design requirements. If the AP installation location needs to be changed, the approval of the design unit and the construction unit must be obtained, and the design change procedures must be completed.

B.When the AP is installed in a weak current well, safety measures such as dust-proof, waterproof and anti-theft should be taken, and the working environment should be well ventilated and clean; when the AP is wall-mounted on the wall of the building, anti-theft measures must be taken; When the AP is installed on the ceiling, it must be fixed with a fixing frame. It is not allowed to be placed in the air or thrown directly on the ceiling. The installation location should be close to the access opening.

C.The hoistway, floor, wall, etc. of the installation location must not seep water, have low dust, and have good ventilation. The installation location must ensure that there are no strong electricity, strong magnets and corrosive equipment. The temperature and humidity of the installation location must not exceed the host. The placement must be good. Lighting conditions to facilitate equipment maintenance and repair

D.The AP must be firmly fixed during installation, and it is not allowed to be placed in the air; the installation location of the AP must have enough space for heat dissipation, debugging and maintenance of the equipment.

Question 67

When the AP's diversity antenna interface is not used, or when doing a distributed system, the power splitter port is not used. In this case, you need to screw it to the interface with _______ to prevent radio frequency interference from affecting the system.

A.1/2" feeder cable

B.RF matching load

C.2dBi gain antenna

D.7/8" feeder cable

Question 68

Which of the following descriptions of the room sub-system is correct? (Multiple choice)

A.The quality of the combined access point directly affects the effect of the two-network integration system. Generally speaking, it is mainly selected on the branch of the GSM/CDMA indoor distribution system. The first will not affect the power distribution of the GSM/CDMA network backbone, and the second can reduce the loss of the WLAN network on the feeder transmission and ensure that power is not wasted.

B.According to the coverage area and the installation location of the combined access point, the power of the two networks needs to be reasonably calculated to determine the installation location of some active devices.

C.If the power of the system is lacking, it is necessary to replace the original transmission feeder of the system or add a power amplifier.

D.In the acceptance test stage, comparisons should be made before and after the combination from the aspects of the system coverage field strength, call quality, handover, call drop, and the influence of the technical parameters of the source base station.

Question 69

Which of the following descriptions of PAP product E PoE power supply requirements is correct? (Multiple choice)

A.The network cable connecting the AP to the upstream PoE power supply device is recommended to be Category 5 or above

B.AP can support PoE module power supply or PoE switch power supply.

C.The length of the network cable is recommended to be within 100 meters when the AP uses PoE power supply

D.There is no requirement for the network cable connecting the AP to the upstream PoE power supply device.

Question 70

For outdoor antenna installation, the wind resistance of the antenna can be ignored.

A.True

B.False

Other Version: 63H3C.Pass4surecert.GB0-341-ENU.v2021-09-26.by.earl.94q.pdf

Latest Upload: 101OCEG.GRCP.v2025-09-11.q211; 101HP.HPE0-V27.v2025-09-11.q78; 117Oracle.1Z0-1057-23.v2025-09-10.q47; 150Google.Professional-Cloud-Network-Engineer.v2025-09-09.q179; 131SAP.C-S4EWM-2023.v2025-09-08.q83; 164TheSecOpsGroup.CNSP.v2025-09-08.q20; 222CFAInstitute.ESG-Investing.v2025-09-08.q173; 157PECB.ISO-IEC-27001-Lead-Implementer.v2025-09-06.q132; 147Salesforce.Data-Architect.v2025-09-05.q216; 141Adobe.AD0-E605.v2025-09-05.q50

Question 66

Question 67

Question 68

Question 69

Question 70

Download PDF File