Question 196
Refer to the exhibit.
A customer needs a server with four 10Gb network adapters. They need it to be configured for the best possible network throughput.
Given the BOM in the exhibit, what do you need to add to this server to meet the customer requirement?
A customer needs a server with four 10Gb network adapters. They need it to be configured for the best possible network throughput.
Given the BOM in the exhibit, what do you need to add to this server to meet the customer requirement?
Question 197
You are installing multiple components into an existing server.
Which HPE resource can you use to verify the compatibility of the server hardware options with the server?
(Select two.)
Which HPE resource can you use to verify the compatibility of the server hardware options with the server?
(Select two.)
Question 198
Read the question, and then refer to the exhibit.
<Switch-A>display int Ten-GigabitEthernet 1/0/1 Ten-GigabitEthernet1/0/1 Current state: UP Line protocol state: UP IP packet frame type: Ethernet II, hardware address: d894-03fb-793d Description: Ten-GigabitEthernet1/0/1 Interface Bandwidth: 10000000 kbps Loopback is not set Media type is stack wire, port hardware type is STACK SFP_PLUS 10Gbps-speed mode, full-duplex mode Link speed type is autonegotiation, link duplex type is autonegotiation Flow-control is not enabled Maximum frame length: 10000 Allow jumbo frames to pass Broadcast max-ratio: 100% Multicast max-ratio: 100% Unicast max-ratio: 100% PVID: 1 MDI type: Automdix Port link-type: Trunk VLAN Passing: 10 VLAN permitted: 10 Trunk port encapsulation: IEEE 802.1q Port priority: 0 <SNIP>
An administrator connected a hypervisor to interface Ten-Gigabit Ethernet1/0/1 in a switch. The administrator created virtual machines in VLAN 10 and 20 on the hypervisor. These VLANs are configured to be tagged on the hypervisor.
The administrator found that all the virtual machines within VLAN 20 can communicate with each other, but not to any resource on VLAN 20 outside the hypervisor.
What must you do to resolve this issue?
<Switch-A>display int Ten-GigabitEthernet 1/0/1 Ten-GigabitEthernet1/0/1 Current state: UP Line protocol state: UP IP packet frame type: Ethernet II, hardware address: d894-03fb-793d Description: Ten-GigabitEthernet1/0/1 Interface Bandwidth: 10000000 kbps Loopback is not set Media type is stack wire, port hardware type is STACK SFP_PLUS 10Gbps-speed mode, full-duplex mode Link speed type is autonegotiation, link duplex type is autonegotiation Flow-control is not enabled Maximum frame length: 10000 Allow jumbo frames to pass Broadcast max-ratio: 100% Multicast max-ratio: 100% Unicast max-ratio: 100% PVID: 1 MDI type: Automdix Port link-type: Trunk VLAN Passing: 10 VLAN permitted: 10 Trunk port encapsulation: IEEE 802.1q Port priority: 0 <SNIP>
An administrator connected a hypervisor to interface Ten-Gigabit Ethernet1/0/1 in a switch. The administrator created virtual machines in VLAN 10 and 20 on the hypervisor. These VLANs are configured to be tagged on the hypervisor.
The administrator found that all the virtual machines within VLAN 20 can communicate with each other, but not to any resource on VLAN 20 outside the hypervisor.
What must you do to resolve this issue?
Question 199
You are installing a combined server and storage solution at a customer location. What must you keep in mind regarding the typical requirements for the location? (Choose two.)
Question 200
A customer has the following requirements:
* two or more 10Gb SFP+ uplinks
* downlink ports capable of 1Gb or 10Gb operation over CAT6a or CAT7 cables.
* 24 downlink ports
Which HPE tool would you use to help choose an HPE network solution that meets the customer requirements?
* two or more 10Gb SFP+ uplinks
* downlink ports capable of 1Gb or 10Gb operation over CAT6a or CAT7 cables.
* 24 downlink ports
Which HPE tool would you use to help choose an HPE network solution that meets the customer requirements?