A frame is the data link layer PDU that encapsulates the network layer PDU (packet) with a header and a trailer that contain information such as source and destination MAC addresses, frame type, error detection, etc. A frame is transmitted over a physical medium such as Ethernet, Wi-Fi, etc. Reference: https://www.arubanetworks.com/techdocs/ArubaOS_86_Web_Help/Content/arubaos-solutions/1-overview/networking-basics.htm

The signal to noise ratio (SNR) is a measure that compares the level of a desired signal to the level of background noise. SNR is defined as the ratio of signal power to the noise power, often expressed in decibels (dB). A high SNR means that the signal is clear and easy to detect or interpret, while a low SNR means that the signal is corrupted or obscured by noise and may be difficult to distinguish or recover3. To calculate the SNR in dB, we can use the following formula:
SNR (dB) = Signal power (dBm) - Noise power (dBm)
In this question, we are given that the noise floor measures -90 dBm (0.000000001 milliwatts) and the receiver's signal strength is -65 dBm (0.000316 milliwatts). Therefore, we can plug these values into the formula and get:
SNR (dB) = -65 dBm - (-90 dBm) SNR (dB) = -65 dBm + 90 dBm SNR (dB) = 25 dBm Therefore, the correct answer is that the SNR is 25 dBm.

Explanation
These commands might help troubleshoot this issue as they check various aspects of the connectivity between the edge switch and the core switch, such as Layer 3 reachability, Layer 2 adjacency, LACP configuration and status, VLAN trunking configuration, and interface status.
References:https://www.arubanetworks.com/techdocs/AOS-CX_10_04/CLI/GUID-8F0E7E8B-0F4B-4A3C-AE7

Explanation
The solid amber radio status LED on an Aruba AP Access Point (AP) Access Point (AP) is a device that connects wireless devices to a wired network using Wi-Fi or other wireless standards . APs act as transmitters and receivers of wireless signals and provide wireless coverage for a specific area . APs can operate in different modes such as root , repeater , bridge , mesh , etc . APs can also support different features such as security , QoS , roaming , load balancing , etc . APs can be standalone devices or managed by controllers or cloud services . APs can be verified by using commands such as show ap active , show ap database , show ap bss-table , etc . indicates that the radio is enabled in monitor or spectrum analysis mode. Monitor mode is a mode that allows the AP to scan all channels and collect information about wireless traffic, interference, rogue devices, etc. Spectrum analysis mode is a mode that allows the AP to scan all channels and collect information about RF Radio Frequency (RF) Radio Frequency (RF) is a term that refers to electromagnetic waves that have frequencies between 3 kHz and 300 GHz . RF waves are used for various purposes such as communication , broadcasting , radar , navigation , remote control , etc . RF waves can be modulated by changing their amplitude , frequency , or phase to encode information . RF waves can also be affected by various factors such as attenuation , reflection , refraction , diffraction , scattering , interference , noise , etc . RF waves can be measured by using devices such as spectrum analyzers , power meters , antennas , etc . environment, noise sources, channel utilization, etc. Both modes are useful for troubleshooting and optimizing wireless performance, but they disable normal data transmission and reception on the radio.
The other options are not indicated by a solid amber radio status LED on an Aruba AP because:
Not enough PoE is provided from the switch to power both radios of the AP: This option is false because not enough PoE Power over Ethernet (PoE) Power over Ethernet (PoE) is a technology that allows network devices to receive power and data over the same Ethernet cable . PoE eliminates the need for separate power sources and cables for devices such as IP phones , cameras , access points , etc .
PoE is defined in IEEE 802.3af and IEEE 802.3at standards and supports different power classes and modes . PoE can be provided by switches or injectors that act as power sourcing equipment (PSE) and received by devices that act as powered devices (PD) . PoE can be verified by using commands suchas show power inline , show power-over-ethernet , debug ip device tracking , etc . is indicated by a blinking amber power status LED on an Aruba AP, not by a solid amber radio status LED. A blinking amber power status LED means that the AP is receiving insufficient power from the switch or injector and cannot operate normally. A solid green power status LED means that the AP is receiving sufficient power from the switch or injector and can operate normally.
The radio is working in mesh mode: This option is false because the radio working in mesh mode is indicated by a solid green radio status LED on an Aruba AP, not by a solid amber radio status LED. A solid green radio status LED means that the radio is working in normal mode or mesh mode and can transmit or receive data on the assigned channel. Mesh mode is a mode that allows the AP to connect wirelessly to other APs and form a mesh network without requiring wired connections.
The radio is working the 5 GHz band only: This option is false because the radio working in the 5 GHz band only is indicated by a solid blue radio status LED on an Aruba AP, not by a solid amber radio status LED. A solid blue radio status LED means that the radio is working in dual-band mode and can transmit or receive data on both 2.4 GHz and 5 GHz bands.
References:
https://www.arubanetworks.com/techdocs/Instant_86_WebHelp/Content/instant-ug/ap-led-behavior.htm
https://www.arubanetworks.com/techdocs/Instant_86_WebHelp/Content/instant-ug/troubleshooting/ap-monitor-m
https://www.arubanetworks.com/techdocs/Instant_86_WebHelp/Content/instant-ug/troubleshooting/ap-spectrum

An AP signal strength of .0000001 milliwatts is equivalent to -80 dBm. The dBm scale is logarithmic, with every 10 dBm representing a tenfold increase or decrease in power. A signal strength of 1 milliwatt (mW) is 0 dBm, so a signal strength of .0000001 mW is 80 decibels less than 1 mW, which is -80 dBm.