Online Access Free JN0-692 Practice Test

Click the Exhibit button.

You have been asked to troubleshoot why an OSPF session will not establish.
Referring to the exhibit, what is the problem?

• A.The OSPF hold-time configuration is set too low.
• B.The OSPF authentication key is incorrectly configured.
• C.The OSPF dead-interval configuration is set too low.
• D.The OSPF authentication type is incorrectly configured.

Click the Exhibit button.
-- Exhibit -user@PE1# show protocols mpls userel-switched-path LSP-1 {
from 101.101.101.1;
to 103.103.103.1; } userel-switched-path LSP-2 {
from 101.101.101.1;
to 103.103.103.1; } interface ge-0/0/0.0;
user@PE1# show protocols ldp interface lo0.0;
user@PE1# show protocols l2circuit
neighbor 103.103.103.1 { interface ge-0/0/3.300 { virtual-circuit-id 300; }
}
user@PE1# show interfaces ge-0/0/3 flexible-vlan-tagging; encapsulation flexible-ethernet-services;
unit 300 { encapsulation vlan-ccc; vlan-id 300;
}
user@PE1# show protocols l2circuit
neighbor 103.103.103.1 { interface ge-0/0/3.300 { virtual-circuit-id 300; community test-community; }
}
user@PE1# show policy-options community test-community members 300:300; -- Exhibit -
Given the topology shown below: CE1-PE1-P-PE2-CE2
PE1 and PE2 have two equal-cost RSVP LSPs (LSP-1 and LSP-2). They form a Layer 2 circuit between CE1 and CE2. You are asked to map their traffic to take LSP-1. The exhibit shows the current configuration of PE1. The correct configuration has been completed on the other routers.
Which two configurations must be added to PE1 to ensure that this traffic is always carried on LSP-1? (Choose two.)

• A.forwarding-table {
  export mapping-l2ckt-to-lsp;
  } user@PE1# show policy-options
• B.policy-statement mapping-l2ckt-to-lsp {
  term 1 {
  from community test-community;
  then {
  install-nexthop lsp LSP-1;
  }
  }
  }
  user@PE1# show policy-options
• C.forwarding-table {
  import mapping-l2ckt-to-lsp;
  }
  user@PE1# show routing-options
• D.policy-statement mapping-l2ckt-to-lsp {
  term 1 {
  from community test-community;
  then {
  accept;
  }
  }
  }
  user@PE1# show routing-options

Click the Exhibit button.


Referring to the exhibit, router r1 has hidden routes in table inet6.0.
Which statement is true?

• A.An IPv4-compatible IPv6 address has not been configured on ge-5/3/0.
• B.ipv6-tunneling must be configured under the [edit protocols mpls] hierarchy.
• C.Router r1 is not receiving any IPv6 routes from its peer.
• D.An IPv4-compatible IPv6 address has not been configured on the loopback interface.

Which two statements are true about the OSPF 2-Way state? (Choose two.)

• A.It is the normal state for two neighbors that are neither the DR nor BDR.
• B.It indicates that communication between two neighbors is bidirectional.
• C.It indicates that a device cannot accept any more full adjacencies.
• D.It is the normal state for neighbors that are the DR and BDR.

Click the Exhibit button.
PIM trace on R1:

You have configured PIM on R1. However, you notice that multicast traffic to 225.20.0.1/32 is dropped. Referring to the exhibit, what is the problem?

• A.Source-specific multicast (SSM) must be configured.
• B.The source is a non-Juniper device.
• C.Reverse-path forwarding check is failing.
• D.The output displayed does not identify any dropped traffic.