Free Access NetworkAppliance.NS0-593.v2022-09-06.q21 Practice Test (Page 5)

Question 16

You Just used the CLI to create a NetApp ONTAP FlexGroup Volume on a NetApp Cloud Volumes ONTAP
instance. After creation, you notice odd behavior in NetApp Cloud Manager.
In this scenario,what Is the reason for this behavior?

A.The Capacity Management Mode within Cloud Manager should be set to Automatic.

B.Cloud Volumes ONTAP does not support FlexGroup volumes.

C.Cloud Manager must be used to provision the FlexGroup volume.

D.The Capacity Management Mode within Cloud Manager should be set to Manual.

Question 17

Your customer Informs you about SnapMlrror problems after upgrading NetApp ONTAP software to a newer
version. After investigating the event logs and the SnapMirror history, you see information about delayed
updates of the SnapMirror relationships.
How would your customer prevent such problems in the future?

A.Modify the schedules of the SnapMirror relationships after upgrading the ONTAP software.

B.Verify that the cabling of the hardware port that Is responsible for SnapMirror transfers Is correct.

C.Delete the SnapMirror relationships and create them new after upgrading the ONTAP software.

D.Quiesce the SnapMirror relationships before upgrading the ONTAP software.

Question 18

Your customer complains that u host will constantly report losing a connection to the iSCSl target and then
report that the session was reestablished.

As shown in the exhibit, what is a cause of this flapping?

A.A host with an IP address of 172.20.10.80 and a second host with an IP address of 10.10.20.60 are
accessing the same LUN.

B.A host with an IP address of 172.20.10.80 and a secondIP address of 10.10.20.60 is accessing different LUNs.

C.A host with an IP address of 172.20.10.80 and a second host with an IP address of 10.10.20.60 have the
same IQN.

D.A host with an IP address of 172.20.10.80 and a secondhost with an IP address of 10.10.20.60 are in
different initiator groups.

Question 19

Referring to the exhibit, from which delay center is most of the latency for voll?

A.Disk

B.NVRAM

C.Network

D.Data

Question 20

After expanding a two-node AFF A300 cluster with two AFF A700 nodes, you observe latencies when data is
accessed indirectly. The system node run -node -command netstat command shows retransmits and packet
drops on the LIFs. The AFF A700 nodes with 40 Gbps and the AFF A300 connect with 10 Gbps to the cluster
interconnect. You are using Cisco Nexus 3132Q cluster interconnect switches. You just updated to ONTAP
9.8 software.
In this scenario, what is causing this problem?

A.The 10 Gbps to 10 Gbps cluster Interconnect is creating a speed mismatch.

B.The AFF A300 Is using an adapter card for the cluster Interconnect, but only onboard ports are supported.

C.AFF A300 and AFF A700 node mixing Isnot supported in ONTAP 9.8 software.

D.There is an NXOS firmware mismatch, verify in the Interoperability Matrix (1MTJ for a supportedversion.

Other Version: 683NetworkAppliance.NS0-593.v2022-08-08.q20

Latest Upload: 107Oracle.1Z0-1057-23.v2025-09-10.q47; 147Google.Professional-Cloud-Network-Engineer.v2025-09-09.q179; 131SAP.C-S4EWM-2023.v2025-09-08.q83; 155TheSecOpsGroup.CNSP.v2025-09-08.q20; 204CFAInstitute.ESG-Investing.v2025-09-08.q173; 152PECB.ISO-IEC-27001-Lead-Implementer.v2025-09-06.q132; 140Salesforce.Data-Architect.v2025-09-05.q216; 136Adobe.AD0-E605.v2025-09-05.q50; 176Nutanix.NCP-MCI-6.10.v2025-09-05.q55; 114Oracle.1z0-591.v2025-09-05.q104

Question 16

Question 17

Question 18

Question 19

Question 20

Download PDF File