Section: Security Operation Adimnistration
Explanation/Reference:
Regression testing is the process of rerunning a portion of the test scenario or test plan to ensure that changes or corrections have not introduced new errors. The data used in regression testing should be the same as the data used in the original test. Unit testing refers to the testing of an individual program or module. Pilot testing is a preliminary test that focuses only on specific and predetermined aspects of a system. Parallel testing is the process of feeding test data into two systems and comparing the results.
Source: Information Systems Audit and Control Association, Certified Information Systems Auditor 2002 review manual, Chapter 6: Business Application System Development, Acquisition, Implementation and Maintenance (page 300).

Section: Network and Telecommunications
Explanation/Reference:
Wireless Transport Layer Security (WTLS) is a communication protocol that allows wireless devices to send and receive encrypted information over the Internet. S-WAP is not defined. WSP (Wireless Session Protocol) and WDP (Wireless Datagram Protocol) are part of Wireless Access Protocol (WAP).
Source: KRUTZ, Ronald L. & VINES, Russel D., The CISSP Prep Guide: Mastering the Ten Domains of Computer Security, John Wiley & Sons, 2001, Chapter 4: Cryptography (page 173).

Section: Network and Telecommunications
Explanation/Reference:
A gateway is used to connect two networks using dissimilar protocols at the lower layers or it could also be at the highest level of the protocol stack.
Important Note:
For the purpose of the exam, you have to remember that a gateway is not synonymous to the term firewall.
The second thing you must remembers is the fact that a gateway act as a translation device.
It could be used to translate from IPX to TCP/IP for example. It could be used to convert different types of applications protocols and allow them to communicate together. A gateway could be at any of the OSI layers but usually tend to be higher up in the stack.
For your exam you should know the information below:
Repeaters
A repeater provides the simplest type of connectivity, because it only repeats electrical signals between cable segments, which enables it to extend a network. Repeaters work at the physical layer and are add-on devices for extending a network connection over a greater distance. The device amplifies signals because signals attenuate the farther they have to travel.
Repeaters can also work as line conditioners by actually cleaning up the signals. This works much better when amplifying digital signals than when amplifying analog signals, because digital signals are discrete units, which makes extraction of background noise from them much easier for the amplifier. If the device is amplifying analog signals, any accompanying noise often is amplified as well, which may further distort the signal.
A hub is a multi-port repeater. A hub is often referred to as a concentrator because it is the physical communication device that allows several computers and devices to communicate with each other. A hub does not understand or work with IP or MAC addresses. When one system sends a signal to go to another system connected to it, the signal is broadcast to all the ports, and thus to all the systems connected to the concentrator.
Repeater

Image Reference- http://www.erg.abdn.ac.uk/~gorry/course/images/repeater.gif Bridges A bridge is a LAN device used to connect LAN segments. It works at the data link layer and therefore works with MAC addresses. A repeater does not work with addresses; it just forwards all signals it receives. When a frame arrives at a bridge, the bridge determines whether or not the MAC address is on the local network segment. If the MAC address is not on the local network segment, the bridge forwards the frame to the necessary network segment.
Bridge

Image Reference- http://www.oreillynet.com/network/2001/01/30/graphics/bridge.jpg Routers Routers are layer 3, or network layer, devices that are used to connect similar or different networks. (For example, they can connect two Ethernet LANs or an Ethernet LAN to a Token Ring LAN.) A router is a device that has two or more interfaces and a routing table so it knows how to get packets to their destinations. It can filter traffic based on access control lists (ACLs), and it fragments packets when necessary. Because routers have more network-level knowledge, they can perform higher-level functions, such as calculating the shortest and most economical path between the sending and receiving hosts.
Router and Switch

Image Reference- http://www.computer-networking-success.com/images/router-switch.jpg Switches Switches combine the functionality of a repeater and the functionality of a bridge. A switch amplifies the electrical signal, like a repeater, and has the built-in circuitry and intelligence of a bridge. It is a multi-port connection device that provides connections for individual computers or other hubs and switches.
Gateways
Gateway is a general term for software running on a device that connects two different environments and that many times acts as a translator for them or somehow restricts their interactions. Usually a gateway is needed when one environment speaks a different language, meaning it uses a certain protocol that the other environment does not understand. The gateway can translate Internetwork Packet Exchange (IPX) protocol packets to IP packets, accept mail from one type of mail server and format it so another type of mail server can accept and understand it, or connect and translate different data link technologies such as FDDI to Ethernet.
Gateway Server

Image Reference- http://static.howtoforge.com/images/screenshots/556af08d5e43aa768260f9e589dc547f-
3024.jpg
The following answers are incorrect:
Repeater - A repeater provides the simplest type of connectivity, because it only repeats electrical signals between cable segments, which enables it to extend a network. Repeaters work at the physical layer and are add-on devices for extending a network connection over a greater distance. The device amplifies signals because signals attenuate the farther they have to travel.
Bridges - A bridge is a LAN device used to connect LAN segments. It works at the data link layer and therefore works with MAC addresses. A repeater does not work with addresses; it just forwards all signals it receives. When a frame arrives at a bridge, the bridge determines whether or not the MAC address is on the local network segment. If the MAC address is not on the local network segment, the bridge forwards the frame to the necessary network segment.
Routers - Routers are layer 3, or network layer, devices that are used to connect similar or different networks. (For example, they can connect two Ethernet LANs or an Ethernet LAN to a Token Ring LAN.) A router is a device that has two or more interfaces and a routing table so it knows how to get packets to their destinations. It can filter traffic based on access control lists (ACLs), and it fragments packets when necessary.
Following reference(s) were/was used to create this question:
CISA review manual 2014 Page number 263
Official ISC2 guide to CISSP CBK 3rd Edition Page number 229 and 230

TACACS+ is a proprietary Cisco enhancement to TACACS and is more robust than RADIUS. PAP is not a remote access authentication system but a remote node security protocol.
Source: KRUTZ, Ronald L. & VINES, Russel D., The CISSP Prep Guide: Mastering the Ten Domains of Computer Security, John Wiley & Sons, 2001, Chapter 3: Telecommunications and Network Security (page 122).

The test environment must be controlled and stable in order to ensure that
development projects are tested in a realistic environment which, as far as possible, mirrors
the live environment.
Reference(s) used for this question:
Information Systems Audit and Control Association, Certified Information Systems Auditor
2002 review manual, chapter 6: Business Application System Development, Acquisition,
Implementation and Maintenance (page 309).