Explanation
To change the swappiness parameter to 0 and make it persistent across reboots and applied immediately, the administrator can perform the following steps:
Append the line vm.swappiness=0 to the file /etc/sysctl.conf using echo "vm.swappiness=0" >>
/etc/sysctl.conf (A). This will set the swappiness parameter to 0 for future boots.
Reload the sysctl configuration using sysctl -p (A). This will apply the changes to the current system without rebooting. The other commands will not achieve this task, but either write to a wrong file, use a wrong option, or have a syntax error. References:
[CompTIA Linux+ Study Guide], Chapter 8: Optimizing Linux Performance, Section: Tuning Kernel Parameters with sysctl
[How to Change Swappiness in Linux]

Explanation
The file /etc/ssh/sshd_config contains the configuration settings for the SSH daemon, which handles the secure remote login. To change the port number, the engineer should edit this file and modify the line that says Port
22 to Port 49000. The other files are not related to the SSH service. References: CompTIA Linux+ (XK0-005) Certification Study Guide, Chapter 13: Managing Network Services, page 411.

Explanation
The message in /var/log/messages indicates that the server is running out of file descriptors. A file descriptor is a non-negative integer identifier for an open file in Linux. Each process has a table of open file descriptors where a new entry is appended upon opening a new file. There is a limit on how many file descriptors a process can open at a time, which depends on the system configuration and the user privileges. If a process tries to open more files than the limit, it will fail with an error message like "Too many open files". This could cause connections to be closed unexpectedly or other problems with the application.
The other options are not correct causes for the connection issue. The process mysqld is not using too many semaphores, which are synchronization mechanisms for processes that share resources. Semaphores are not related to file descriptors or open files. Something is not starving the server resources, which could mean high CPU usage, memory pressure, disk I/O, network congestion, or other factors that affect performance. These could cause slowdowns or timeouts, but not file descriptor exhaustion. The amount of RAM allocated to the server is not too high, which could cause swapping or paging if it exceeds the physical memory available. This could also affect performance, but not file descriptor availability. References: File Descriptor Requirements (Linux Systems); Limits on the Number of Linux File Descriptors

Explanation
The command restorecon -R -v /var/www/html will best resolve the issue. The issue is caused by the incorrect SELinux context of the web server files under the /var/www/html directory. The output of ls -Z
/var/www/html shows that the files have the type user_home_t, which is not allowed for web content. The command restorecon restores the default SELinux context of files based on the policy rules. The options -R and -v are used to apply the command recursively and verbosely. This command will change the type of the files to httpd_sys_content_t, which is the correct type for web content. This will allow the web server to access the files and serve the pages to the browser. The other options are incorrect because they either disable SELinux entirely (sed -i 's/SELINUX=enforcing/SELINUX=disabled/'
/etc/selinux/config or setenforce 0), which is not a good security practice, or enable an unnecessary boolean (setsebool -P httpd_can_network_connect_db on), which is not related to the issue. References: CompTIA Linux+ (XK0-005) Certification Study Guide, Chapter 18: Securing Linux Systems, page 535.

Explanation
The command semanage port -a -t http_port_t -p tcp 6379 adds a new port definition to the SELinux policy and assigns the type http_port_t to the port 6379/tcp. This allows the web application to run on this port and accept connections from users. This is the correct way to resolve the issue. The other options are incorrect because they either delete a port definition (-d), use the wrong protocol (top instead of tcp), or list the existing port definitions (-l). References: CompTIA Linux+ (XK0-005) Certification Study Guide, Chapter 18:
Securing Linux Systems, page 535.