Free Access Cisco.200-301.v2022-04-26.q191 Practice Test (Page 11)

Question 46

Refer to the exhibit.

An engineer deploys a topology in which R1 obtains its IP configuration from DHCP. If the switch and DHCP server configurations are complete and correct. Which two sets of commands must be configured on R1 and R2 to complete the task? (Choose two)

A.R1(config)# interface fa0/0
R1(config-if)#ip helper-address 192.0.2.2

B.R2(config)# interface gi0/0
R2(config-if)#ip address dhcp

C.R1(config)# interface fa0/0
R1(config-if)#ip address dhcp
R1(config-if)# no shutsown

D.R1(config)# interface fa0/0
R1(config-if)#ip helper-address 198.51.100.100

E.R2(config)# interface gi0/0
R2(config-if)#ip helper-address 198.51.100.100

Question 47

What is recommended for the wireless infrastructure design of an organization?

A.configure the first three access points are configured to use Channels 1, 6, and 11

B.include a least two access points on nonoverlapping channels to support load balancing

C.group access points together to increase throughput on a given channel

D.assign physically adjacent access points to the same Wi-Fi channel

Question 48

Which action is taken by a switch port enabled for PoE power classification override?

A.If a monitored port exceeds the maximum administrative value for power, the port is shutdown and err-disabled

B.If a switch determines that a device is using less than the minimum configured power it assumes the device has failed and disconnects

C.As power usage on a PoE switch port is checked data flow to the connected device is temporarily paused

D.When a powered device begins drawing power from a PoE switch port a syslog message is generated

Question 49

Which two tasks must be performed to configure NTP to a trusted server in client mode on a single network device? (Choose two)

A.Enable NTP authentication.

B.Verify the time zone.

C.Disable NTP broadcasts

D.Specify the IP address of the NTP server

E.Set the NTP server private key

Question 50

Refer to the exhibit. If configuring a static default route on the router with the ip route 0.0.0.0 0.0.0.0 10.13.0.1 120 command, how does the router respond?

A.It ignores the new static route until the existing OSPF default route is removed

B.It immediately replaces the existing OSPF route in the routing table with the newly configured static route

C.It starts load-balancing traffic between the two default routes

D.It starts sending traffic without a specific matching entry in the routing table to Gigabit EthernetO/1

Other Version: 2429Cisco.200-301.v2025-02-15.q952; 2132Cisco.200-301.v2024-12-17.q416; 1388Cisco.200-301.v2024-05-18.q342; 3978Cisco.200-301.v2023-07-13.q727; 2124Cisco.200-301.v2023-03-13.q260; 6776Cisco.200-301.v2022-11-15.q593; 7552Cisco.200-301.v2022-06-18.q420; 74Cisco.Braindumpspass.200-301.v2021-11-30.by.nathan.105q.pdf; 8033Cisco.200-301.v2021-09-11.q243; 105Cisco.Examcollectionpass.200-301.v2021-09-09.by.rose.243q.pdf

Latest Upload: 105OCEG.GRCP.v2025-09-11.q211; 104HP.HPE0-V27.v2025-09-11.q78; 118Oracle.1Z0-1057-23.v2025-09-10.q47; 153Google.Professional-Cloud-Network-Engineer.v2025-09-09.q179; 131SAP.C-S4EWM-2023.v2025-09-08.q83; 166TheSecOpsGroup.CNSP.v2025-09-08.q20; 229CFAInstitute.ESG-Investing.v2025-09-08.q173; 176PECB.ISO-IEC-27001-Lead-Implementer.v2025-09-06.q132; 152Salesforce.Data-Architect.v2025-09-05.q216; 148Adobe.AD0-E605.v2025-09-05.q50

Question 46

Question 47

Question 48

Question 49

Question 50

Download PDF File