Free Access Cisco.300-615.v2022-10-01.q126 Practice Test (Page 20)

Question 91

An IOM fails during a firmware upgrade and is unresponsive. Which action recovers the module?

A.Restore UCSM configuration from backup.

B.Roll back to the previous firmware.

C.Use AutoInstall to reinstall the firmware.

D.From the peer IOM, reset the faulty module.

Question 92

Refer to the exhibit.

HSRP adjacency fails to form between Nexus7K-1 and Nexus7K-2. Which action should be taken to solve the problem?

A.Configure preempt on one of the switches in the HSRP group.

B.Configure the correct subnet mask on Nexus7K-1.

C.Configure the same HSRP priority between the two switches.

D.Configure HSRP version 2 on Nexus7K-2.

Question 93

Refer to the exhibit.

An engineer is configuring boot from iSCSI on a Cisco UCS B-Series Blade Server, but the LUN fails to mount. Which action resolves the issue?

A.Configure an MTU size of 9000 on the appliance port.

B.Set a connection timeout value of 250 in the iSCSI Adapter Policy.

C.Statically configure the target information in the Boot Policy.

D.Configure a QoS policy on the vNIC.

Question 94

Refer to the exhibit.

A client configures an upgrade of its Cisco Nexus switches that are connected to the Cisco ACI controller, such that the switches are upgraded one at a time. After the upgrade is run, it is discovered that both Cisco Nexus switches were upgraded simultaneously. Which two actions ensure that the switches upgrade one at a time? (Choose two.)

A.Choose the 'Pause upon upgrade failure" Run Mode

B.Place each leaf switch in a different upgrade group

C.Select the "Graceful Maintenance" checkbox

D.Check the Ignore Compatibility" checkbox

E.Configure the *Do not pause on failure and do not wait on cluster health" Run Mode

Question 95

Refer to the exhibit. A network engineer is configuring the FCoE N_Port virtualization storage area network. After the initial implementation, server 11 fails to connect to the disk array. Which action resolves the issue?

A.On N9K interface vfc11 and MDS interface vfc 1/1, change switchport mode configuration to F

B.On MDS interface vfc 1/1, change switchport mode configuration to VF

C.On N9K interface vfc11, change switchport mode configuration to NP

D.On N9K interface vfc11 and MDS interface vfc 1/1, change switchport mode configuration to E

Other Version: 808Cisco.300-615.v2024-09-25.q117; 1034Cisco.300-615.v2023-01-31.q58; 2686Cisco.300-615.v2022-05-28.q107; 2739Cisco.300-615.v2022-05-03.q107; 93Cisco.Exams4sures.300-615.v2021-11-23.by.tess.99q.pdf

Latest Upload: 203PaloAltoNetworks.NGFW-Engineer.v2026-05-01.q43; 302Nokia.4A0-113.v2026-05-01.q69; 264EC-COUNCIL.312-49v11.v2026-04-30.q214; 230Microsoft.MB-820.v2026-04-30.q101; 213Salesforce.MC-202.v2026-04-30.q57; 207BICSI.INSTC_V8.v2026-04-29.q53; 337NMLS.MLO.v2026-04-28.q82; 245NCARB.Project-Management.v2026-04-28.q27; 466EMC.D-AV-DY-23.v2026-04-27.q184; 1125ServiceNow.CSA.v2026-04-27.q483

Question 91

Question 92

Question 93

Question 94

Question 95

Download PDF File