Section: Access Control
Explanation/Reference:
Administrative, technical and physical controls are categories of access control mechanisms.
Logical and Technical controls are synonymous. So both of them could be eliminated as possible choices.
Physical Controls: These are controls to protect the organization's people and physical environment, such as locks, gates, and guards. Physical controls may be called "operational controls" in some contexts.
Physical security covers a broad spectrum of controls to protect the physical assets (primarily the people) in an organization. Physical Controls are sometimes referred to as "operational" controls in some risk management frameworks. These controls range from doors, locks, and windows to environment controls, construction standards, and guards. Typically, physical security is based on the notion of establishing security zones or concentric areas within a facility that require increased security as you get closer to the valuable assets inside the facility. Security zones are the physical representation of the defense-in-depth principle discussed earlier in this chapter. Typically, security zones are associated with rooms, offices, floors, or smaller elements, such as a cabinet or storage locker. The design of the physical security controls within the facility must take into account the protection of the asset as well as the individuals working in that area.
Reference(s) used for this question:
Hernandez CISSP, Steven (2012-12-21). Official (ISC)2 Guide to the CISSP CBK, Third Edition ((ISC)2 Press) (Kindle Locations 1301-1303). Auerbach Publications. Kindle Edition.
and
Hernandez CISSP, Steven (2012-12-21). Official (ISC)2 Guide to the CISSP CBK, Third Edition ((ISC)2 Press) (Kindle Locations 1312-1318). Auerbach Publications. Kindle Edition.

The 802.11 standard outlines how wireless clients and APs communicate, lays out the specifications of their interfaces, dictates how signal transmission should take place, and describes how authentication, association, and security should be implemeted.
The following answers are incorrect:
Public Key Infrastructure (PKI) Public Key Infrastructure is a supporting infrastructure to manage public keys. It is not part of the IEEE 802 Working Group standard.
Packet-switching technology A packet-switching technology is not included in the IEEE 802 Working Group standard. It is a technology where-in messages are broken up into packets, which then travel along different routes to the destination.
The OSI/ISO model The Open System Interconnect model is a sevel-layer model defined as an international standard describing network communications.
The following reference(s) were/was used to create this question:
Source: Shon Harris - "All-in-One CISSP Exam Guide" Fourth Edition; Chapter 7 Telecommunications and Network Security: pg. 624.
802.11 refers to a family of specifications developed by the IEEE for Wireless LAN technology. 802.11 specifies an over-the-air interface between a wireless client and a base station or between two wireless clients. The IEEE accepted the specification in 1997. There are several specifications in the 802.11 family:
802.11 # applies to wireless LANs and provides 1 or 2 Mbps transmission in the 2.4 GHz band using either frequency hopping spread spectrum (FHSS) or direct sequence spread spectrum (DSSS). 802.11a # an extension to 802.11 that applies to wireless LANs and provides up to 54 Mbps in the 5GHz band. 802.11a uses an orthogonal frequency division multiplexing encoding scheme rather than FHSS or DSSS. 802.11b (also referred to as 802.11 High Rate or Wi-Fi) # an extension to 802.11 that applies to wireless LANS and provides 11 Mbps transmission (with a fallback to 5.5, 2 and 1 Mbps) in the 2.4 GHz band. 802.11b uses only DSSS. 802.11b was a 1999 ratification to the original 802.11 standard, allowing wireless functionality comparable to Ethernet. 802.11g # applies to wireless LANs and provides 20+ Mbps in the 2.4 GHz band.
Source: 802.11 Planet's web site.

Section: Risk, Response and Recovery
Explanation/Reference:
The main advantage of the qualitative impact analysis is that it prioritizes the risks and identifies areas for immediate improvement in addressing the vulnerabilities. It does not provide specific quantifiable measurements of the magnitude of the impacts, therefore making a cost-analysis of any recommended controls difficult. Since it involves a consensus of export and some guesswork based on the experience of Subject Matter Experts (SME's), it can not be easily automated.
Reference used for this question:
STONEBURNER, Gary et al., NIST Special publication 800-30, Risk management Guide for Information Technology Systems, 2001 (page 23).

Explanation/Reference:
Updating records in multiple locations or copying an entire database to a remote location as a means to ensure the appropriate levels of fault-tolerance and redundancy is known as Database shadowing.
Shadowing is the technique in which updates are shadowed in multiple locations. It is like copying the entire database on to a remote location.
Shadow files are an exact live copy of the original active database, allowing you to maintain live duplicates of your production database, which can be brought into production in the event of a hardware failure. They are used for security reasons: should the original database be damaged or incapacitated by hardware problems, the shadow can immediately take over as the primary database. It is therefore important that shadow files do not run on the same server or at least on the same drive as the primary database files.
The following are incorrect answers:
Data mirroring In data storage, disk mirroring is the replication of logical disk volumes onto separate physical hard disks in real time to ensure continuous availability. It is most commonly used in RAID 1. A mirrored volume is a complete logical representation of separate volume copies.
Backups In computing the phrase backup means to copy files to a second medium (a disk or tape) as a precaution in case the first medium fails. One of the cardinal rules in using computers is back up your files regularly. Backups are useful in recovering information or a system in the event of a disaster, else you may be very sorry :-(
Archiving is the storage of data that is not in continual use for historical purposes. It is the process of copying files to a long-term storage medium for backup.
Reference(s) used for this question:
Hernandez CISSP, Steven (2012-12-21). Official (ISC)2 Guide to the CISSP CBK, Third Edition ((ISC)2 Press) (Kindle Locations 27614-27626). Auerbach Publications. Kindle Edition.
http://en.wikipedia.org/wiki/Disk_mirroring
http://www.webopedia.com/TERM/A/archive.html
http://ibexpert.net/ibe/index.php?n=Doc.DatabaseShadow

Section: Security Operation Adimnistration
Explanation/Reference:
Absolute/Direct
+------+-----+--------------------------------------+
| load | reg | address |
+------+-----+--------------------------------------+
(Effective address = address as given in instruction)
This requires space in an instruction for quite a large address. It is often available on CISC machines which have variable-length instructions, such as x86.
Some RISC machines have a special Load Upper Literal instruction which places a 16-bit constant in the top half of a register. An OR literal instruction can be used to insert a 16-bit constant in the lower half of that register, so that a full 32-bit address can then be used via the register-indirect addressing mode, which itself is provided as "base-plus-offset" with an offset of 0.
http://en.wikipedia.org/wiki/Addressing_mode (Very good coverage of the subject) also see:
Source: KRUTZ, Ronald L. & VINES, Russel D., The CISSP Prep Guide: Mastering the Ten Domains of Computer Security, page 186.
also see:
http://www.comsci.us/ic/notes/am.html