Section: Infrastructure Services

Explanation
The summary-address is only used to create aggregate addresses for OSPF at an autonomous system boundary.
It means this command should only be used on the ASBR when you are trying to summarize externally redistributed routes from another protocol domain or you have a NSSA area. But a requirement to create a summarized route is:
The ASBR compares the summary route's range of addresses with all routes redistributed into OSPF on that ASBR to find any subordinate subnets (subnets that sit inside the summary route range). If at least one subordinate subnet exists, the ASBR advertises the summary route.

VLAN access control lists (VACLs) provide network-security enforcement based on Layer 2, Layer 3, and Layer
4 information on a VLAN.
VACLs can be used to provide security based on MAC address, source and destination IP address, Layer 4 protocols, or port numbers. The VACL will act on all traffic of a select VLAN whether bridged or switched. The actions performed on a packet can include permit, redirect, or deny. The VACL entries are checked in sequence, which is similar in concept to route-map structures. The following procedure is used to create VACLs:
Define a VLAN access map:
switch(config)# vlan access-map name [seq#]
Configure a match clause:
switch(config-access-map)# match {ip address {1-99 | 1300-2699 | acl_name} | mac address acl_name} Configure an action clause:
switch(config-access-map)# action {drop | forward | redirect}
Apply the map to a VLAN:
switch(config)# vlan filter map_name vlan-list list
Once created, you should verify the VACLs using the following commands:
switch# show vlan access-map map_name
switch# show vlan filter
In the sample configuration shown below, all VLAN traffic in VLANS 1 through 3 that match access list SAFE will be forwarded. All other traffic will be dropped.
switch(config)# vlan access-map cisco 10
switch(config-access-map)# match ip-address SAFE
switch(config-access-map)# action forward
switch(config)# vlan filter cisco vlan-list 1-3
If access list cisco were configured as shown below, for example, traffic with a source address of 172.16.10.8 would be dropped.
Switch# show ip access-list cisco 10
Extended ip access list cisco 10
10 permit 10.0.0.0 255.255.255.0 any
Objective:
Infrastructure Security
Sub-Objective:
Configure and verify switch security features
References:
Cisco > Home > Support > Product Support > End-of-Sale and End-of-Life Products > Cisco Catalyst 6000 Series Switches > Configure > Configuration Examples and Technotes > Securing Networks with Private VLANs and VLAN Access Control Lists Cisco > Cisco IOS LAN Switching Command Reference > vlan access-map Cisco > Cisco IOS LAN Switching Command Reference > match (vlan access-map)

Explanation
Same Answer is already updated below:

HTTP and HTTPs run on TCP port 80 and 443, respectively and we have to remember them.
Syslog runs on UDP port 514 while NTP runs on UDP port 123 so if we remember them we can find out the matching answers easily. But maybe there is some typos in this question as 2001:d88:800:200c::c/126 only ranges from 2001:d88:800:200c:0:0:0:c to 2001:d88:800:200c:0:0:0:f (4 hosts in total). It does not cover host 2001:0D88:0800:200c::1f. Same for 2001:D88:800:200c::e/126, which also ranges from
2001:d88:800:200c:0:0:0:c to 2001:d88:800:200c:0:0:0:f and does not cover host 2001:0D88:0800:200c::1c
.