Free Access Cisco.300-425.v2026-05-10.q276 Practice Test (Page 8)

Question 31

As part of a wireless site survey in a hospital, an engineer needs to identify potential Layer 1 interferers. In which two areas is the engineer most likely to find sources of 2.4 GHz and 5 GHz RF noise? (Choose two.)

A.magnetic resonance imaging

B.kitchen

C.Gamma Knife radiation treatment

D.X-ray radiography

E.patient room

Question 32

A network engineer is working for an enterprise where most of the laptops support 802.11v. To optimize the client roaming experience, configuration changes must be made on the corporate SSID to force clients to use the best APs based on the 802.11 v BSS transition message. Which configuration meets this requirement?

A.Enable BSS transition for the SSID and disable dissociation imminent to avoid client disconnects.

B.Disable coverage hole detection and enable 802.11k for the corporate SSID.

C.Enable coverage hole detection and BSS transition and disable dissociation imminent.

D.Enable the BSS transition option with an optimized roaming timer for the corporate SSID.

Question 33

A technician connects a Cisco Aironet 3700 Series access point to a switch and realizes that the AP is coming up with 3x3 MIMO. Which reason explains this behavior?

A.A redundant power supply is unavailable on the switch.

B.The switch is 802.3af capable.

C.The AP is getting power from a power injector.

D.The switch is PoE+ capable.

Question 34

Which statement about creating a mobility group is true, excluding mobility anchors?

A.Each WLC must use the same mobility domain name and be defined as a peer in each other's static mobility members list.

B.If WLCs with HA SSO are deployed, each WLC in the WLC HA pair is considered separately as a mobility peer.

C.The WLCs do not have to be of the same model or type to be a member of a mobility group, however each member should be running different software versions.

D.A mobility group does not require all WLCs in the group to use the same virtual IP address.

Question 35

An engineer is designing a new wireless network. The network needs to meet these requirements:

Which design approach should be taken?

A.5 GHz frequency band with channel bonding, to support 40 MHz channels

B.5 GHz frequency band without channel bonding, to support 20 MHz channels

C.5 GHz frequency band with channel bonding, to support 80 MHz channels.

D.2.4 GHz frequency band without channel bonding, to support 20 MHz channels

Other Version: 1098Cisco.300-425.v2026-02-23.q330; 2486Cisco.300-425.v2022-10-21.q114; 2782Cisco.300-425.v2022-05-21.q101; 2824Cisco.300-425.v2022-04-20.q100; 45Cisco.Trainingdump.300-425.v2021-11-16.by.jeremy.94q.pdf; 1491Cisco.300-425.v2021-11-12.q33

Latest Upload: 206Cisco.300-610.v2026-08-19.q170; 193CompTIA.PT0-003.v2026-08-19.q179; 153Databricks.Databricks-Generative-AI-Engineer-Associate.v2026-08-18.q40; 147SAP.C_CR125_2601.v2026-08-17.q28; 210Salesforce.Field-Service-Consultant.v2026-08-17.q134; 167Oracle.1Z0-1170.v2026-08-16.q64; 173Oracle.1Z1-1170.v2026-08-16.q64; 199Juniper.JN0-336.v2026-08-13.q60; 371EMC.NCP-AII.v2026-08-13.q200; 219CIRO.RSE.v2026-08-12.q41

Question 31

Question 32

Question 33

Question 34

Question 35

Download PDF File