Increasing the glazing area in an office building affects various aspects of energy consumption due to changes in heat gain, heat loss, and natural light availability, but it does not influence all buildingsystems. The EDGE User Guide explains the impacts of glazing: "Increasing the glazing area (window-to-wall ratio, WWR) in an office building typically increases cooling demand due to higher solar heat gain, increases heating demand in colder climates due to greater heat loss through windows, and reduces lighting energy by allowing more natural daylight, assuming proper daylighting design" (EDGE User Guide, Section 3.5: Passive Design Strategies). Option A (cooling demand) is affected, as more glazing increases solar heat gain: "Higher WWR leads to greater cooling loads in hot climates due to increased solar radiation entering the building" (EDGE Methodology Report Version 2.0, Section 5.2: Energy Calculation Methods). Option B (heating demand) is also impacted, particularly in cooler climates: "Larger glazing areas increase heat loss in cold climates, raising heating demand due to the lower thermal resistance of windows compared to walls" (EDGE User Guide, Section 4.1: Insulation Measures). Option C (lighting energy) is affected, as more glazing can reduce the need for artificial lighting: "Increased glazing can lower lighting energy by enhancing daylight penetration, provided glare is controlled" (EDGE User Guide, Section 4.4: Lighting Efficiency Measures). However, Option D (hot water demand) is not impacted by glazing area, as hot water use is tied to occupant activities (e.
g., showers, cleaning) rather than building envelope design: "Hot water demand in EDGE is determined by occupant use patterns, such as the number of showers or laundry cycles, and is not influenced by glazing area or WWR" (EDGE Methodology Report Version 2.0, Section 4.2: Water Savings Calculations). The EDGE User Guide further confirms: "Glazing area impacts energy-related metrics like cooling, heating, and lighting, but has no direct effect on hot water demand, which is calculated separately based on usage assumptions" (EDGE User Guide, Section 5.2: Water Efficiency Measures). Therefore, increasing glazing area does not impact hot water demand (Option D).
Reference:EDGE User Guide Version 2.1, Section 3.5: Passive Design Strategies, Section 4.1: Insulation Measures, Section 4.4: Lighting Efficiency Measures, Section 5.2: Water Efficiency Measures; EDGE Methodology Report Version 2.0, Section 5.2: Energy Calculation Methods, Section 4.2: Water Savings Calculations.

Under the CBCI EDGE curriculum, EDGE Certified and EDGE Advanced are one-time certifications and do not require renewal. EDGE Zero Carbon is treated differently because it depends on ongoing operational conditions, especially how the building's remaining operational emissions are addressed through renewable electricity and, where applicable, offsets. For this reason, EDGE Zero Carbon certificates include an expiration date and require renewal to confirm that the carbon strategy remains valid over time.
The EDGE Zero Carbon rules specify different expiration periods depending on how the project achieves the renewable electricity and emissions balance. When a project meets the EDGE Zero Carbon criteria fully on- site, including the generation of on-site renewable electricity, the certificate expires after four years. This longer validity period reflects the higher confidence and stability associated with on-site renewable generation that is physically tied to the building and less dependent on external contracts or market instruments.
By comparison, projects that rely on purchased off-site renewable electricity and or carbon offsets have a shorter certificate validity period because procurement terms and availability can change. Therefore, for a fully on-site renewable electricity EDGE Zero Carbon project, the correct expiration period is four years.

The EDGE App relies on location-specific climate data to calculate resource savings, but not all cities are listed. The EDGE User Guide provides guidance for such cases: "If the project city is not listed in the EDGE App, the user should choose the closest city to the project location that is available in the database. If necessary, the user can edit the climate data (e.g., temperature, humidity) to better reflect the project's actual conditions, ensuring accurate calculations" (EDGE User Guide, Section 2.2: Project Setup). Option B, choose the closest city and edit the climate data if necessary, directly matches this protocol. Option A (write to EDGE Certifier and wait) is incorrect, as this is not a required step: "Users are not required to request new cities; they can proceed by selecting the closest city" (EDGE User Guide, Section 2.2: Project Setup). Option C(select any city in the same climate zone globally) is too broad and inaccurate: "Choosing a city from a different region, even in the same climate zone, may lead to incorrect assumptions about local practices and climate" (EDGE Methodology Report Version 2.0, Section 3.2: Climate Data Inputs). Option D (choose the capital city) is also incorrect unless it is the closest: "The capital city should only be selected if it is the nearest available option in the database" (EDGE User Guide, Section 2.2: Project Setup). Thus, the correct protocol is to choose the closest city and edit climate data (Option B).
Reference:EDGE User Guide Version 2.1, Section 2.2: Project Setup; EDGE Methodology Report Version
2.0, Section 3.2: Climate Data Inputs.

Occupancy sensors in the EDGE software are part of energy efficiency measures aimed at reducing unnecessary energy use by automating system operation based on occupant presence. The EDGE User Guide explicitly defines their application: "Occupancy sensors in EDGE are used for controlling lighting in internal areas, automatically turning lights off when spaces are unoccupied to reduce energy consumption. This measure, often listed as EEM23 - Occupancy Sensors for Lighting, can achieve significant savings in buildings with intermittent occupancy, such as offices or schools" (EDGE User Guide, Section 4.4: Lighting Efficiency Measures). Option A, lighting, directly matches this description, as occupancy sensors are primarily associated with lighting control in EDGE. Option B (water taps) is incorrect, as occupancy sensors are not used for water systems in EDGE: "Water taps may be controlled by sensors in some projects, but this is not a recognized measure in EDGE, which focuses on measures like low-flow fixtures for water savings" (EDGE User Guide, Section 5.2: Water Efficiency Measures). Option C (air conditioners) is also incorrect, as occupancy sensors for HVAC are not a standard measure in EDGE: "While occupancy sensors can theoretically control air conditioners, EDGE does not include this as a measure; HVACefficiency is addressed through measures like variable speed drives or efficient chillers" (EDGE Methodology Report Version 2.0, Section 5.1: Energy Efficiency Metrics). Option D (external lighting) is not applicable, as EDGE specifies occupancy sensors for internal areas: "Occupancy sensors in EDGE are applied to internal lighting, not external lighting, which may use timers or photocells instead" (EDGE User Guide, Section 4.4: Lighting Efficiency Measures). The EDGE Methodology Report further confirms: "The energy savings from occupancy sensors in EDGE are calculated based on reduced lighting hours in internal spaces, reflecting typical usage patterns in commercial buildings" (EDGE Methodology Report Version 2.0, Section 5.4:
Lighting Calculations). Thus, occupancy sensors are used for controlling lighting (Option A).
Reference:EDGE User Guide Version 2.1, Section 4.4: Lighting Efficiency Measures, Section 5.2: Water Efficiency Measures; EDGE Methodology Report Version 2.0, Section 5.1: Energy Efficiency Metrics, Section 5.4: Lighting Calculations.

The role of an EDGE Auditor during a design audit (Preliminary Certification stage) is to verify compliance with the EDGE standard, which requires at least 20% savings in energy, water, and embodied energy in materials. If the project does not meet the standard, the Auditor must follow specific protocols without overstepping their role. The EDGE Expert and Auditor Protocols outline the acceptable actions: "If a project does not meet the EDGE standard for energy during a design audit, the Auditor should inform the Client of the shortfall and ask them to use the EDGE tool again to identify additional measures that will take the project comfortably over the EDGE standard (e.g., 20% energy savings). The Auditor must not provide design advice or modify the assessment themselves, as their role is to verify, not consult" (EDGE Expert and Auditor Protocols, Section 4.1: Audit Process). Option A, ask the Client to use the EDGE tool again to identify options that will take the project comfortably over the EDGE standard, directly aligns with this guidance, as it keeps the Auditor in a verification role while encouraging the Client to revise their design. Option B (contact the design team directly to work with them) is incorrect, as it violates the Auditor's independence: "The Auditor must not engage directly with the design team to improve the project, as this constitutes consultancy, which conflicts with their role as an independent verifier" (EDGE Expert and Auditor Protocols, Section 2.3:
Conflict of Interest). Option C (take no further action) is also incorrect, as the Auditor has a responsibility to report the shortfall: "If a project does not meet the EDGE standard, the Auditor must document the failure in the audit report and inform the Client, rather than abandoning the process" (EDGE Certification Protocol, Section 3.2: Audit Requirements). Option D (provide a list of measures based on the Auditor's experience) oversteps the Auditor's role by offering consultancy: "The Auditor cannot provide specific design recommendations or measures, as this compromises their impartiality; they must direct the Client to use the EDGE software or consult an EDGE Expert" (EDGE Expert and Auditor Protocols, Section 2.3: Conflict of Interest). The EDGE User Guide further supports: "During a design audit, the Auditor's role is to assess compliance, not to guide the design process; if the project falls short, the Client should revisit the EDGE tool to explore additional measures, potentially with the help of an EDGE Expert" (EDGE User Guide, Section
6.5: Working with EDGE Auditors). The EDGE Certification Protocol adds: "The Auditor's report should note the energy shortfall and recommend that the Client revise the self-assessment to meet the 20% savings threshold, ensuring the process remains Client-driven" (EDGE Certification Protocol, Section 3.2: Audit Requirements). Thus, asking the Client to use the EDGE tool again (Option A) is the acceptable course of action.
Reference:EDGE Expert and Auditor Protocols, Section 4.1: Audit Process, Section 2.3: Conflict of Interest; EDGE Certification Protocol, Section 3.2: Audit Requirements; EDGE User Guide Version 2.1, Section 6.5:
Working with EDGE Auditors.